Thursday, May 27, 2010

GPP Thursday Quickie Week 0524

This week's GPP Thursday Quickie, is more of a reminder. We are very close to the launch of our new www.GReddy.com in early June (maybe even next week!) But to make it better we need your help with some more user photos. In exchange for using your photo, we will send you a free GReddy Key-chain. For more details and specifics please see our two previous post on the subject...

Thank you for your support!

http://greddy-usa.blogspot.com/2010/01/we-need-your-exhaust-photos.html






http://greddy-usa.blogspot.com/2010/05/we-also-need-your-greddy-turbo-ic.html






You can send your photos and info to greddyusa@greddy.com or to our Facebook Fan Page.

Tuesday, May 25, 2010

Another quick photoshoot for the 370Z


Yesterday the weather was great here in Southern California. Just perfect for a photoshoot and our 370Z was ready for some overseas photographers. If you followed us on Twitter you saw a couple sneak-peeks. But here are a few more photos of our Twin Turbo (453whp Z34) 370Z...





Tuesday, May 18, 2010

Product Release: R35 DCT cooler

In addition to the introduction of our new Evo X SST trans cooler, also have a great cooling system for the DCT (Dual Clutch Transmission) found on the R35 GTR

It features our famous Blue (inner-fin) large 13row core mounted in front fender. It also includes a FRP divided air duct, similar to the OEM unit on the other side of the car for maximum cooling.



Installation is easy thanks to specialized GReddy R35 trans oil block. The internal thermostat insures quick fluid warm-up and consistent oil temps, and does not tax the standard coolant system.


Carefully designed light-weight -14 hard-lines & braided-lines allow for a minimal routing lengths and maximum flow. Completing the kit are all the necessary mounts, hose fitting and 3 piece billet flanges with o-rings.


Also available as an option, is our GReddy R35 Window Washer Tank option. This is ideal to keep you window washer working even with use of either our DCT or front-mounted Intercooler kits.


Thursday, May 13, 2010

GReddy Paper Craft 2

Here is a quick little project for you GReddy Fans. Print out the image below, cut it out along the thick black lines and fold along the thin black lines. Then glue at the * points. And then you should end up with your very own GReddy R35. Have Fun!

When your finished, email us a photo to greddyusa@greddy.com, we might have some stickers for you, if you live with in the USA. (or if you live out of side of the USA, send a print out image of your completed paper-craft, with a self-addressed envelope with the proper postage and we'll use you pre-paid envelope to send you out your free stickers)

Monday, May 10, 2010

GReddy R35 Twin Turbo Kit Movie



Check out this movie featuring the install and running of our Twin TD06SH-20G turbo upgrade kit for the R35 GTR. With skilled tuning the kit can make upwards of 1000hp and provide consistent and reliable 9sec quarter mile passes.

Thursday, May 6, 2010

CZ4A Circuit Spec Cooler Kits

GReddy is proud to announce the production of some much need products for hard driving Evolution X, with two new Circuit Spec Cooler Kits. The V-mounted SST (MR -twin clutch transmission) and Engine Oil Coolers increase the efficiency of the OEM coolers, by increasing the fluid capacity and cooling surface area, while controlling and improving air-flow to the cores.

The factory SST transmission found on Evolution X MR are known to trigger a "Safety" limp mode when the internal fluid hits 140C (284F,) which is not difficult to do during hard driving.

The GReddy SST Cooler Kit uses an additional independent system with it's own compact 160l/hr pump for superior cooling. It is easily installed by connecting to the existing fluid "Filler" and "Drain" ports on the transmission case. (NO machining required.) The V-mount arrangement is mounted in the front left inner fender under the factory unit (and to fit it, it also includes a new aluminum I/C outlet piping.) Another benefit, is that vital areas, like the Radiator, are not covered. The kit also includes carefully designed Inlet and Splitter Ducting to evenly divide and control airflow through both the GReddy and OEM cores, while the Outlet Ducting helps increases flow. The V-mounted 12row (-08) GReddy core takes advantage of the airflow under the vehicle to draw out even more air through the core (,while the stock core has to fight with the air turbulence of the spinning wheel in the wheel well.) Also included are precise patterns for trimming of the under liner.


Tested at Tsukuba Circuit, Japan, with one test driver, and two identical CZ4A Evolution X s with SST transmissions.
After about 16min of circuit driving, the factory equipped car reads 140C and the ECU engages a 2000RPM limiter.
The GReddy equipped Evo, drove on for 30min, without any adverse effects to performance.



Mounted in a symmetrical configuration as our SST Cooler the GReddy Circuit Spec Engine Oil Cooler Kit mounts in the right inner fender under the factory core. Like our other Circuit spec kits this V-mounted 14row (-10) core uses our signature inner fin technology for high efficiency. This greatly helps improve the durability of the engine oil and in turn the life of the engine. The kit adapts to the factory cooler and routes the oil in series, for an simple install. The kit also features carefully crafted Inlet, Splitter, and Outlet Air Ducting to increase flow to and through both the GReddy and factory coolers. Light-weight Nylon-braided hose add to the upgrades on this kit; as does the necessary trimming patterns for a perfect fit.



Tested at Tsukuba Circuit, Japan, with one test driver, and two identical CZ4A Evolution Xs with SST transmissions (1 Stock, and 1 with both GReddy Circuit Spec Coolers.)
The GReddy equipped Evo show consistent
engine oil temperatures in the 90-100C range, even under hard circuit driving.
While the factory car showed already showed over 130C (266F) engine oil temp., when the SST triggered the safety mode at 14min.


* Both kits can work with OEM fog-lights, with air ducting trimming.
* GReddy SST cooler can be activated by a manual switch or by the GReddy MSS (Multi Switching System.)

Monday, May 3, 2010

We also need your GReddy Turbo & IC pictures...

Hello GReddy Turbo & Intercooler Kit Owners!

We are currently working on the next version of our homepage: www.GReddy.com (coming soon!) And like we explained in our Exhaust Photo Campaign, we know we could use more good photos of our GReddy parts in use. That is where you can help us.

Send us an image you have taken of your GReddy Turbo or Intercooler on your Car and if we end up using the image, we will send you some FREE GReddy Keychain...

Keychain


What we are looking for in a good GReddy Turbo or GReddy Intercooler photo is:


1. Minimum Size: W:600 x H:400 pixels at 72dpi

2. Clear view of a GReddy Turbocharger or Intercooler installed on your car.

3. It is best when we can tell what kind of car it is installed on.

4. So it is best if the full bumper, headlights are visible for intercooler pictures.

5. And the engine for turbo kit pictures

6. By submitting your photos, you agree that you have the rights to the images you are sending and you give GReddy full rights to use the images for our websites and promotional materials.


7. And most importantly we need a full description of all your info.


EXAMPLE:
Name: Eddy Rex Racer
Your Location: California
Vehicle Make: Nissan
Vehicle Model: 370Z
Vehicle Year: 2009
GReddy Turbo or Intercooler Type: Type 24 Vspec
• Emailed to greddyusa@greddy.com (Subject: GReddy Photo)

Or you can also "Share" & "Attach a photo" directly to our "Fan Wall" on our
GReddy Fan Page on Facebook

Before we use the photo, we will first contact you by email or FB for your full contact info.
We need this info to send you out your Key-chain. Unfortunately we can not use all the photos that are submitted, but we really do appreciate all who send in photos! We thank you for your support.

Here are some good examples of what we are looking for at different angles (see below...)